Ventis MX4 Gas Monitor
The Ventis MX4 is a portable multi-gas monitor. When purchased as a diffusion monitor, it detects and measures gases present in open space. The Ventis MX4 is also offered as an aspirated monitor. A pump module and battery accessories enable the conversion of either monitor for dedicated use in either confined or open spaces. Based on the customer’s monitor order, up to four sensors are factory installed enabling the monitor to continuously and simultaneously detect and measure the presence of up to four specific gases.
Availability: Commercially available
+1 412 788 4353
1001 Oakdale Road
Oakdale, PA 15071
USA
|
|
www.indsci.com
| Manufacturer |
| Industrial Scientific Corporation |
| Product Name |
| Ventis MX4 Gas Monitor |
| Detection Category |
| Chemical |
| Detection Principle |
| Sensors; |
| Detection Method |
| Electrochemical Detection; |
| Application |
| Gas Analysis; |
| Equipment Type |
| Instrument |
| Product Synopsis |
| The Ventis MX4 is a portable multi-gas monitor. When purchased as a diffusion monitor, it detects and measures gases present in open space. The Ventis MX4 is also offered as an aspirated monitor. A pump module and battery accessories enable the conversion of either monitor for dedicated use in either confined or open spaces. Based on the customer’s monitor order, up to four sensors are factory installed enabling the monitor to continuously and simultaneously detect and measure the presence of up to four specific gases. |
| Availability |
| Commercially available |
| Technology Readiness Level (TRL) |
| 9 |
| User Feedback Sources |
| Indifferent/No user feedback |
| Dimensions |
| 4.1 x 2.3 x 1.2 in (105 x 59 x 31 mm) (including pump): 6.8 x 2.6 x 2.6 in (173 x 67 x 67 mm) |
| Weight |
| <1 lb.; Ventis MX4:182 g (6.4 oz) Ventis MX4 with pump: 380 g (13.4 oz) |
| Power Requirements |
| Lithium Battery; Alkaline Battery; Rechargeable lithium-ion battery pack; Rechargeable extended-range lithium-ion battery pack; Replaceable AAA alkaline battery pack (20 hours) |
| Noise Produced |
| 95 db |
| Transportability |
| Handheld |
| Ruggedness |
| Extreme Temperatures/Humidity; |
| Operating Conditions |
| –20 to 50°C (–4 to 122°F) ;15 to 95%Rh, non-condensing |
| Consumables |
| <$1,000/year; Calibration gas, sensors, tubing |
| Solvents/Reagents |
| Calibration gas |
| Calibration Schedule |
| Daily and before field use Monthly bump test, Quick-Cal calibration mode is used to calibrate all sensors simultaneously with one cylinder of blended calibration gas |
| Suggested Routine Maintenance |
| Replacement of sensors |
| Available Accessories |
| Docking station; calibration station; battery chargers; carrying cases; confined space kit |
| Data Analysis Support Equipment |
| Docking station and I-net Ready (An instrument management system) |
| Communications Interface |
| Docking Station using a cross over or Ethernet cable |
| Expected Operational Life |
| 8 years |
| Shelf Life |
| <5 years; Some sensors expire in 18 to 24 months. Some sensors last 3 to 5 years. |
| Unit Cost |
| $975.00 |
| Maintenance Cost |
| $150 to $650 depending on the sensor |
| Other Chemical Targets |
| Combustible gases, methane, oxygen, carbon monoxide, hydrogen sulfide, nitrogen dioxide, and sulfur dioxide |
| Sample Introduction |
| Vapor/Gas |
| Sensitivity/Detection Limits |
| ppm |
| Start Up Time (From Cold Start To Sample Ready) |
| < 30 seconds |
| Response Time (Sample Application To Output) |
| <5 minutes; Low or high settings, up to 2 minutes plus 2 seconds per/ft if a tube is used |
| Total Run Time |
| < 3 minutes |
| Alarm Capability |
| Audible, visual and vibrational |
| Software Control |
| On-board |
| Training Required |
| <1 day training |
| Training Available |
| Video training |
| Manuals Available |
| Operator’s Manual Quick Start Guides |
| Warranties |
| 2 year warranty also includes sensors and battery |
| IATA Shipping Restrictions |
| Yes; IATA regulations apply for calibration gases |
| Approved Vendors |
| Grainger; Hagemeyer; Orr Safety Corp.; Wilson Supply Co. |