D16 Portable Gas Leak Detector
The D16 Portable Gas Leak Detector is a tool for performing regular leak checks in gas storage areas, around process equipment and piping, or in confined spaces prior to entry. Designed for one-hand operation, the detector contains an internal sample pump and a flexible sampling wand to help locate the source of the detected gas. Detection is accomplished by means of “smart sensor modules” consisting of a sensor, amplifier and memory module in a single removable package. Only one sensor module may be installed in the D16 at a time, but the vendor claims that the detector can be reconfigured for a new gas in less than a minute.
Availability: Commercially Available
| Manufacturer |
| Analytical Technology, Inc. |
| Product Name |
| D16 Portable Gas Leak Detector |
| Detection Category |
| Chemical |
| Detection Principle |
| Sensors; |
| Detection Method |
| Electrochemical Detection; |
| Application |
| Emergency Response; Gas Analysis; |
| Equipment Type |
| Instrument |
| Product Synopsis |
| The D16 Portable Gas Leak Detector is a tool for performing regular leak checks in gas storage areas, around process equipment and piping, or in confined spaces prior to entry. Designed for one-hand operation, the detector contains an internal sample pump and a flexible sampling wand to help locate the source of the detected gas. Detection is accomplished by means of “smart sensor modules” consisting of a sensor, amplifier and memory module in a single removable package. Only one sensor module may be installed in the D16 at a time, but the vendor claims that the detector can be reconfigured for a new gas in less than a minute. |
| Availability |
| Commercially Available |
| Technology Readiness Level (TRL) |
| 9 |
| User Feedback Sources |
| Indifferent/No user feedback |
| Dimensions |
| 3.5 x 9.0 x 5.5 in (8.9 x 22.9 x 14 cm) |
| Weight |
| <30 Lbs.; 7 Lbs. (3.2 kg) |
| Power Requirements |
| Alkaline Battery; NiMH Battery; D cell battery, internal NiCd rechargeable for backup power |
| Transportability |
| Handheld |
| Ruggedness |
| Extreme Temperatures/Humidity |
| Operating Conditions |
| –25 to 55°C (-13 to 131°F), 0 to 95% RH |
| Consumables |
| <$1,000/year; Sensors |
| Calibration Schedule |
| Sensors calibrated independently then loaded into detector |
| Suggested Routine Maintenance |
| Replacement of sensors—$275 to $550 |
| Available Accessories |
| Carrying case, sampling wand, spare filters, flow meter, battery charger, RS-232 output cable, spare D cell battery, calibration “T” fitting |
| Data Analysis Support Equipment |
| Optional PC, Software |
| Communications Interface |
| RS-232, USB |
| Expected Operational Life |
| Indefinite |
| Shelf Life |
| <5 years; 2 years |
| Unit Cost |
| $1,150.00 |
| Maintenance Cost |
| $200 to $500/year |
| Tested For ITF-25 TIC/TIMs |
| Bromine, chlorine, fluorine, ammonia, carbon monoxide, phosgene, hydrogen chloride, hydrogen cyanide, hydrogen fluoride, hydrogen sulfide, nitrogen dioxide, sulfur dioxide, arsine, diborane, hydrogen selenide, phosphine, ethylene oxide, formaldehyde, methane, carbon dioxide |
| Sample Introduction |
| Vapor/Gas |
| Sensitivity/Detection Limits |
| ppb |
| Known Interferents/Inhibitors |
| May false alarm to high concentrations of some smokes and engine exhausts |
| Start Up Time (From Cold Start To Sample Ready) |
| 1 minute |
| Response Time (Sample Application To Output) |
| <1 minute |
| Total Run Time |
| Minutes |
| Alarm Capability |
| Audible and Visual |
| Software Control |
| Software provided to allow data transfer via RS-232 |
| Training Required |
| <1 day training |
| Training Available |
| Formal Training |
| Manuals Available |
| Yes |
| Reachback Service |
| Not Specified |
| Warranties |
| 1 year parts and labor |
| Approved Vendors |
| www.gas-sensing.com |
